Guide · Homeowners · 3 min read · Updated 17 November 2026
What Happens During a Damp Survey? A Step-by-Step Guide
Short answer
During a damp survey a surveyor inspects the outside of the building for defects such as bridged damp courses, blocked gutters and high ground, then takes moisture readings, humidity and surface temperature measurements inside. Where needed they drill samples for carbide or salt testing and lift floorboards. A typical house takes one to three hours on site, followed by a written report within a few days.
Before the visit
A good surveyor asks questions before arriving. When did the damp first appear? Is it worse in winter? Has anyone treated it before? Do you dry washing indoors? These answers narrow down the likely causes. You will also be asked to clear access to the affected walls, the loft hatch and any cellar or under-stairs cupboard.
Try not to run a dehumidifier or heat the room unusually hard in the days before the survey. That can mask the pattern the surveyor needs to see, particularly with condensation.
The outside inspection
Most damp starts outside, so the survey usually does too. The surveyor walks around the building looking at the damp-proof course line, the height of paths and flower beds against the walls, the condition of render and pointing, gutters, downpipes, window sills, flashings and chimney stacks. Blocked or buried air bricks are noted because they affect ventilation under timber floors.
A path laid too high, render carried down over the damp course or a leaking downpipe can explain an internal damp patch without any treatment to the wall itself.
- Ground levels relative to the damp-proof course
- Render, pointing and cracked masonry
- Gutters, downpipes, hoppers and drains
- Sills, flashings, roof edges and chimneys
- Air bricks and sub-floor ventilation
Inside: readings and measurements
Inside, the surveyor uses a moisture meter to map where readings are high and how the pattern changes with height. Rising damp tends to show a band of dampness up to about a metre, highest at the bottom. Penetrating damp often shows patches linked to an outside defect. Condensation produces high readings on cold surfaces, corners and behind furniture.
Hygrometers measure air humidity and surface thermometers or infrared cameras show cold spots. From these the surveyor can work out the dew point and whether surfaces are cold enough for condensation to form. Thermal imaging can also help trace hidden leaks and missing insulation.
The surveyor will also look at how the home is used. Drying clothes on radiators, unvented tumble dryers, extractor fans that do not run and bedrooms with windows never opened all add moisture to the air. These details are recorded because they explain condensation patterns that readings alone cannot.
Where a plumbing leak is suspected, the surveyor may check under sinks, around baths and showers, and at radiator pipes running into solid floors. A localised damp patch that stays wet in dry weather and does not follow a horizontal band is a common sign of a leak rather than a building defect.
| Tool | What it measures | Limitations |
|---|---|---|
| Electrical moisture meter | Relative surface moisture pattern | Salts and foil-backed finishes give false highs |
| Carbide meter | Actual moisture content of drilled samples | Needs small holes drilled into mortar or brick |
| Hygrometer | Air temperature and relative humidity | A single reading is only a snapshot |
| Infrared thermometer or camera | Surface temperatures and cold spots | Shows temperature, not moisture directly |
| Salt analysis | Chlorides and nitrates from the ground | Results usually take a few days from a lab |
Sampling and opening up
If rising damp is suspected, a surface meter is not enough. Salts in old plaster attract moisture from the air and make walls read high even when no water is coming up from the ground. The surveyor may drill small samples from the mortar at different heights and test them with a carbide meter, or send them for salt analysis. That is the kind of evidence BS 6576 describes before rising damp is confirmed.
Where timber floors are involved, the surveyor may lift a board or two to check joists and wall plates for rot and to see whether the void is ventilated. They will tell you before doing anything that leaves a mark.
How long it takes and what you receive
A flat or small house with one problem area typically takes about an hour on site. A full house damp and timber survey can take two to three hours, longer with cellars and roof voids. The written report usually follows within a few working days, or longer if samples have gone to a laboratory.
The report should explain what type of damp is present, the evidence for it, the cause, and the recommended repairs in order of priority. Cheaper fixes such as lowering ground levels or clearing gutters should come before chemical treatment. If a report jumps straight to injection without explaining why, ask questions before booking any work.
Preparing your home for the survey
A little preparation makes the visit quicker and the findings more reliable. Move furniture at least half a metre away from affected walls, clear the floor along skirtings and lift rugs where floor timbers might need checking. Make sure the loft hatch and cellar door can be opened and that there is a light or torch available for dark spaces.
Gather any paperwork relating to earlier damp or timber treatment, including guarantees, invoices and old reports. Note when the damp is at its worst and take photos over a few weeks if the pattern changes. The surveyor will also want to know whether the property has been empty, recently redecorated or had any recent plumbing work, since all of these affect readings.
Questions people also ask
Do I need to be home for a damp survey?
It helps to be present, or to have someone there who knows the property. The surveyor will ask about the history of the damp, previous repairs and how the home is heated and ventilated. If you cannot attend, a tenant or agent can provide access, but send the background details in writing beforehand.
Will the surveyor drill holes in my walls?
Only if sampling is needed. Carbide and salt tests require small holes drilled into mortar joints or plaster, usually a few millimetres wide. A good surveyor explains this beforehand and chooses discreet spots. Electrical meter readings use two small pins that leave pinprick marks, which are barely visible on most finishes.
Can a damp survey be done in summer?
Yes. Rising and penetrating damp can be diagnosed at any time of year, although condensation problems are easier to see in colder months when windows stream and walls are cold. If your problem is mainly winter mould, mention this so the surveyor can measure surface temperatures and humidity with seasonal conditions in mind.
Written and checked by the Damp Survey team. Read our editorial policy.
More guides
How Much Does a Damp Survey Cost in the UK?
A damp survey in the UK costs £150–£300 for a flat or small house where one to three areas are affected, and £250–£500 for a full house damp and…
Independent Damp Survey vs Free Survey: Which Should You Choose?
An independent damp survey is carried out by a surveyor who charges a fee and sells no treatment, so their diagnosis is not tied to a sale. A free…
Damp Survey When Buying a House: What Buyers Need to Know
If a mortgage valuation or homebuyer report flags damp, book a specialist pre-purchase damp and timber survey before exchange. It costs £250–£450,…
How to Read a Damp Survey Report (and Spot a Bad One)
A good damp survey report states what type of damp is present, shows the evidence such as readings, photos and test results, explains the cause, and…
Get a free damp survey quote
Tell us what you need and we'll come back with a clear price.
Request a quote